Quidway WB2011 Betriebsanweisung Seite 62
- Seite / 157
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
System Configuration
5-18
5
MAC Address – The physical layer address of the wireless bridge unit at the other
end of the wireless link. (12 hexadecimal digits in the form “xx:xx:xx:xx:xx:xx”)
Port Status – Enables or disables the wireless bridge link.
Note: The wireless MAC address for each bridge unit is printed on the label on the
back of the unit.
CLI Commands for WDS – The following example shows how to configure the MAC
address of the wireless bridge at the opposite end of a point-to-point link, and then
enable forwarding on the link.
Bridge
The wireless bridge can store the MAC addresses for all known devices in the
connected networks. All the addresses are learned by monitoring traffic received by
the wireless bridge and are stored in a dynamic MAC address table. This information
is then used to forward traffic directly between the Ethernet port and the wireless
interface.
The Bridging page allows the MAC address aging time to be set for both the
Ethernet port and the wireless radio interface. If the MAC address of an entry in the
address table is not seen on the associated interface for longer than the aging time,
the entry is discarded.
Outdoor Bridge(config)#wds mac-address 1 00-12-34-56-78-9a 6-31
Outdoor Bridge(config)#wds enable 6-31
Outdoor Bridge(config)#exit
Outdoor Bridge#show wds 6-32
Outdoor_Mode : SLAVE
==================================================
Port ID | Status | Mac-Address
==================================================
01 | ENABLE | 00-12-34-56-78-9A
==================================================
Outdoor Bridge#
- User Guide 1
- Outdoor 5 GHz Wireless Bridge 3
- F1.1.1.0 E102004-R01 4
- Compliances 5
- Safety Compliance 6
- Contents 14
- Chapter 1: Introduction 15
- Hardware Description 16
- Ethernet Port 17
- Power Injector Module 17
- Introduction 18
- Grounding Point 18
- System Configuration 19
- Features and Benefits 20
- System Defaults 21
- Data Rates 23
- Radio Path Planning 24
- Antenna Height 25
- Bridge Link Planning 26
- Radio Interference 27
- Weather Conditions 27
- Ethernet Cabling 28
- Grounding 28
- Testing Basic Link Operation 29
- Mount the Unit 29
- Hardware Installation 30
- Connect the External Antenna 32
- Ground Wire 33
- Ethernet Cable 33
- Align Antennas 34
- RSSI BNC 35
- Connection 35
- Initial Setup through the CLI 37
- Initial Configuration Steps 38
- Initial Configuration 40
- 4. Click Finish 43
- Advanced Configuration 45
- System Identification 46
- TCP / IP Settings 47
- Filter Control 50
- Administration 54
- Upgrading Firmware 55
- System Log 57
- Enabling System Logging 58
- Configuring SNTP 59
- Spanning Tree Protocol (STP) 65
- Radio Interface 69
- Normal Mode 70
- Turbo Mode 70
- Security 72
- Status Information 77
- Station Status 79
- Event Logs 80
- Chapter 6: 81
- Entering Commands 82
- Partial Keyword Lookup 83
- Using Command History 83
- Understanding Command Modes 84
- Exec Commands 84
- Configuration Commands 84
- Command Line Processing 85
- Command Groups 86
- General Commands 86
- System Management Commands 90
- System Logging Commands 96
- Command Line Interface 100
- System Clock Commands 101
- SNMP Commands 103
- Flash/File Commands 107
- WDS Commands 110
- Bridge Commands 113
- Filtering Commands 120
- Ethernet Interface Commands 123
- Wireless Interface Commands 127
- VLAN Commands 138
- Appendix A: Troubleshooting 141
- Troubleshooting 142
- Appendix B: Specifications 143
- 10/100BASE-TX Pin Assignments 145
- Straight-Through Wiring 146
- Crossover Wiring 146
- 8-Pin DIN Connector Pinout 147
- Cables and Pinouts 148
- Glossary 149
- WEP 5-28, 6-53 154
- E102004-R01 157
Samsung SAMSUNG ST200F manuali
Manuali dei proprietari e guide per l'utente per no Samsung SAMSUNG ST200F.
We fornisce 5 manuali pdf Samsung SAMSUNG ST200F per scaricare gratuitamente in base al tipo di documento: Manuale Utente
Kommentare zu diesen Handbüchern